Bullbar paint

thevfr87

New Member
G'day, just wanting some advice for painting my grey bullbar Gloss black, including the matte black around the headlights, any ideas on what is a good paint, where to get. cheers!
 

prawns

Moderator
Alloy bar mate?

You sure you dont want to just polish it up? I managed this without even any metal polish just some elbow grease and a rag with nothing on it (using proper polish would make the job easy)

Reckon they look good when all nice and polished (mind you its a ongoing thing)

bar1.JPG


omg just noticed your name and avatar - Dont tell me we both drive NH pajeros and both ride bikes? (i got a gixxer)

Are you my long lost brother? :D
 
Last edited:

thevfr87

New Member
Correct and correct! had bike L's before car p's, so technically, i guess i coulda ridden a hayabusa, but not been allowed to drive an SS! have a VFR with a blown hg. nah, it has a steel bar. had it 3 months, and It's a beast!
 

thevfr87

New Member
Alloy bar mate?

You sure you dont want to just polish it up? I managed this without even any metal polish just some elbow grease and a rag with nothing on it (using proper polish would make the job easy)

Reckon they look good when all nice and polished (mind you its a ongoing thing)

bar1.JPG


omg just noticed your name and avatar - Dont tell me we both drive NH pajeros and both ride bikes? (i got a gixxer)

Are you my long lost brother? :D



hey prawns, just thought i'd ask, as we both have NH's, hows your tailgate sitting, mine isn't flush at the top, almost like the door has flexed over the years, but i'm wondering if theres a hinge adjustment, or if theres more out there like this... cheers.
 

joebog

New Member
I would use White Night brand killrust paint
about $30 a litre just clean up decently and its a nice job
Im gonna paint my BB with satin BUT same paint

Joe
 

muc the truck

Well-Known Member
why not use 2 pac auto motive paint for flatand gloss colours like black white etc its about 34 dollars a litre from protec.
Protec - Paint, Value, Support

hardener is about 20 bucks for 500ml reducer 13 bucks a litre that will give you almost 1.7 ltrs of top quality paint.
believe it or not if you add a little reducer you can brush it on and it will flow so as there is no brush strokes and its easy to paint with out side in full ventilation once in a blue moon with no ill side effects.

there is also a flatning agent for about 20 bucks that you can add to gloss paint to make it matt. this will be cheaper than buying 2 cans of pant , one gloss and one matt.

I am brushing flat black 2pac on al my galvanised rails around my deck as spraying would get it everywhere. its 12mm solid square balustrades and you cant see a single brush stroke. covers about 12m2 per litre. awesome weatherproof

brushes wash out in acrylic lacquer thinners, or just toss them away.

hope this helps.
 
Last edited:

03hilux

4x4 Earth Contributer
Gavo is right fellas. There is no need to be nasty or belittle people un necessarily. There is nothing wrong with answering someone's question with what you think is the right method.
Now back to the OP,

The suggestion of using a satin paint, It would give a nice clean look without looking dull.

Make sure you either sand the BB well, or have it sand blasted, and the use a good quality primer that is compatible with your final paint choice.
 

joebog

New Member
Paint

THANKS again 03 hilux,
the escaped locksmith is even more negative than I am!!!

ANYWAY, before it rained on MY parade I got 7/8the of my bullbar done
Ill post full details when its finished ( maybe tomorrow )
and as nobody even shit on my ideas I just welded it like I did :p:p:p:p
its still dead square, and feels solid, I banged my head on it, and it didnt bend at all.

So thanks for the help all:) < smiling pleasantly :p

anyway, this will be painted with satin killrust ( white knight brand) epoxy enamel. As I do go bush I bugger the paint fairly often, and its really easy to touch up, which is why I recommended it in the first place.
The origional bar is powder coated ( or was anyway) and the satin blends almost perfectly

Chat tomorrow

regards to all

Joe
 

Attachments

  • one_side_done.jpg
    one_side_done.jpg
    196 KB · Views: 2,349

prawns

Moderator
hey prawns, just thought i'd ask, as we both have NH's, hows your tailgate sitting, mine isn't flush at the top, almost like the door has flexed over the years, but i'm wondering if theres a hinge adjustment, or if theres more out there like this... cheers.

My tailgate sits level along the top, but seems to be shaped slightly wierd when looking from the back (convex) Both left and right sides of the tailgate are recessed under the chrome water channel above the rear tailgate, but the middle of the tailgate is actually flush with the water channel above it

Not sure if thats what you mean or not - but the only adjustment Ive done on the rear door was to stop a squeak noise - I did this by opening the tailgate, and moving the big rubber block which has a couple bolts in it, I moved it further out so the tailgate had to "climb the rubber block" earlier on and was pressed against it harder once the tailgate was shut. Havnt noticed any other adjustments on the door to be honest
 

PJR NSW

Banned
I painted the parts of my original Toyota alloy one that could be seen from the cabin with a coat of etch primer and then a coat of flat black. Both spray cans were of the cheaper variety. Still in good nick after three years when I sold the bar which had been replaced.

Phil
 

Soot

New Member
I would look at powder coating. It is a lot cheaper then people think and i is very resistant to stone chips and scratching.
 

brumbypt

Banned
I stripped the old powder coating off and then painted it with a good quality paint..

now everytime I scratch it I can paint it easily.. keeps it looking nice, all the time.




Carry on...
 

Bush Ranger

Active Member
I would look at powder coating. It is a lot cheaper then people think and i is very resistant to stone chips and scratching.
I was thinking of powder coating my bull bar. One quote was for $220 from a place that does every thing from a to z. The second place does industrial equipment and quoted me $440 in Satin Black. Couldn`t believe the price difference between the two. Pays to shop around.
 

brumbypt

Banned
a weekend, plus $50 or less in paint.. to do it ya self.. or $100 for 4lts of kill rust etc.

do it yaself.


Carry on...
 

muc the truck

Well-Known Member
I have spent over years thousands on powedercoating and not anymore .
what ever it is if its kept long enough and used in 4x4 situations it chips and delaminates.
If it its powder coted over steel and it chips not only is there missing coating there is areas on the edges were water collects and rusts when wet due to it coming away . To make things worse you cant sand blast it off. some not normally available to public strippers will get it off but the only thing the average bloke can buy redily to remove the crap is GASKET STRIPPER. and a lot off it.

STRONGLY URGE 4x4 owners to keep using paint . atleast you can repair it
 

muc the truck

Well-Known Member
I would look at powder coating. It is a lot cheaper then people think and i is very resistant to stone chips and scratching.

NO it is NOT , I agree its cheap but that's all. it chips and scratches a lot more than good 2pac paint.
 

brumbypt

Banned
I have heard since that u can paint over the powerdercoat, as long as its got a good hold of the metal that its on..

so ya sand it back, scrap off any chipped bits etc. then paint..

too easy..


Carry on...
 

hiluxdriver

Well-Known Member
I would look at powder coating. It is a lot cheaper then people think and i is very resistant to stone chips and scratching.

I looked into this also. I rang around and got some quotes to sandblast ad powdercoat. Cheapest was $300 up to $500.
 

chris_stoffa

4x4 Earth Contributer
If your looking for flat , flat black and long lasting try aerosol Pot Belly Black Stove paint. the longer it stays on there and the hotter the sun is that heats the bull bar the tougher the stuff gets , even better if you can get it baked in an oven.:D

I use the stuff on gun barrels, bake it to 200-220 C and the finish is as tough as buggery.

And its cheap and shyte easy to touch up :D
 
Top